More Parts Added

theenginebuilder · Post by **theenginebuilder** » Sat Oct 15, 2011 3:18 pm

More new parts added.
http://www.honda600carparts.com

Mark P Hatten · Post by **Mark P Hatten** » Sat Oct 15, 2011 7:13 pm

Awesome ! you've got some very much needed parts for great prices
http://www.mphspecialties.com/
To: 2cylinderhondas@yahoogroups.com From: theenginebuilder@...
Date: Sat, 15 Oct 2011 22:18:32 +0000 Subject: [2cylinderhondas] More Parts Added
More new parts added.
http://www.honda600carparts.com

friend · Post by **friend** » Sun Oct 16, 2011 8:16 am

I wouldn't go so far as to qualify these as good parts. Something off the shelf for a different application may not work and cause more problems than you had to begin with. Natural Rubber works well with water but not with oil, there are a bunch of O rings out there made for a different purpose. Many of the shaft seals sold by Honda are directional. None of the seals listed have that capacity. Often a seal is not all that is needed to correct the problem, the sealing surface may also need repair. It may fit the housing but will it seal against the rotating shaft? You may have noticed the Fan Mount cushions on your engine swelling because of oil leaking onto them. If you replaced them with Neoprene rubber they will resist swelling and last much longer. The question - have they been tested on a Honda 600 engine? for how long and with what result? In a vehicle or just on a test stand?
Bill

> -----Original Message-----
> From:
> 2cylinderhondas@yahoogroups.com [mailto:2cylinderhondas@yahoogroups.com] > On > Behalf Of > Mark P Hatten > Sent:
> Saturday, October 15, 2011 5:27
> PM
> To:
> 2cylinderhondas@yahoogroups.com
> Subject:
> RE:
> [2cylinderhondas] More Parts Added
> Awesome ! you've got some very much needed parts for great > prices
> http://www.mphspecialties.com/
> To: 2cylinderhondas@yahoogroups.com
> From:
> theenginebuilder@...
> Date: Sat, 15 Oct 2011 22:18:32
> +0000
> Subject: [2cylinderhondas] More Parts
> Added
> More new parts added.
> http://www.honda600carparts.com

robertjritter · Post by **robertjritter** » Sun Oct 16, 2011 4:48 pm

I have bought many parts from this site and have been very happy with all the parts I have received and the custom service.

--- In
2cylinderhondas@yahoogroups.com
, wrote:
> I wouldn't go so far as to qualify these as good parts. Something off the
> shelf for a different application may not work and cause more problems than
> you had to begin with. Natural Rubber works well with water but not with
> oil, there are a bunch of O rings out there made for a different purpose.
> Many of the shaft seals sold by Honda are directional. None of the seals
> listed have that capacity. Often a seal is not all that is needed to
> correct the problem, the sealing surface may also need repair. It may fit
> the housing but will it seal against the rotating shaft? You may have
> noticed the Fan Mount cushions on your engine swelling because of oil
> leaking onto them. If you replaced them with Neoprene rubber they will
> resist swelling and last much longer. The question - have they been tested
> on a Honda 600 engine? for how long and with what result? In a vehicle or
> just on a test stand?
> Bill
> -----Original Message-----
> From:
2cylinderhondas@yahoogroups.com
> [mailto:
2cylinderhondas@yahoogroups.com
]On Behalf Of Mark P Hatten
> Sent: Saturday, October 15, 2011 5:27 PM
> To:
2cylinderhondas@yahoogroups.com
> Subject: RE: [2cylinderhondas] More Parts Added
> Awesome ! you've got some very much needed parts for great prices
http://www.mphspecialties.com/
> ----------------------------------------------------------------------------
> --
> To:
2cylinderhondas@yahoogroups.com
> From: theenginebuilder@...
> Date: Sat, 15 Oct 2011 22:18:32 +0000
> Subject: [2cylinderhondas] More Parts Added
> More new parts added.
http://www.honda600carparts.com

Random Name · Post by **Random Name** » Sun Oct 16, 2011 5:02 pm

Do they have a parts page or online catalog?
Kurt

On Oct 16, 2011, at 4:48 PM, "robertjritter" wrote:
I have bought many parts from this site and have been very happy with all the parts I have received and the custom service.
--- In
2cylinderhondas@yahoogroups.com
, wrote:
> I wouldn't go so far as to qualify these as good parts. Something off the
> shelf for a different application may not work and cause more problems than
> you had to begin with. Natural Rubber works well with water but not with
> oil, there are a bunch of O rings out there made for a different purpose.
> Many of the shaft seals sold by Honda are directional. None of the seals
> listed have that capacity. Often a seal is not all that is needed to
> correct the problem, the sealing surface may also need repair. It may fit
> the housing but will it seal against the rotating shaft? You may have
> noticed the Fan Mount cushions on your engine swelling because of oil
> leaking onto them. If you replaced them with Neoprene rubber they will
> resist swelling and last much longer. The question - have they been tested
> on a Honda 600 engine? for how long and with what result? In a vehicle or
> just on a test stand?
> Bill
> -----Original Message-----
> From:
2cylinderhondas@yahoogroups.com
> [mailto:
2cylinderhondas@yahoogroups.com
]On Behalf Of Mark P Hatten
> Sent: Saturday, October 15, 2011 5:27 PM
> To:
2cylinderhondas@yahoogroups.com
> Subject: RE: [2cylinderhondas] More Parts Added
> Awesome ! you've got some very much needed parts for great prices
http://www.mphspecialties.com/
> ----------------------------------------------------------
> --
> To:
2cylinderhondas@yahoogroups.com
> From: theenginebuilder@...
> Date: Sat, 15 Oct 2011 22:18:32 +0000
> Subject: [2cylinderhondas] More Parts Added
> More new parts added.
http://www.honda600carparts.com

friend · Post by **friend** » Sun Oct 16, 2011 6:21 pm

Bob;
That may be true, and it is not just this site I am speaking of. There were people selling vinyl tubing to be used with brake fluid that was made for water. The seals pictured are not directional and there is no mention of the material they are made of. If it were a substantiated company such as Beck Arnley or WIX there would be no hesitation and I would agree.
But who knows? Oh they may run for a while but why would Honda make them directional if it didn't have to? And, if the O rings are made of Natural Rubber they will swell when used with oil and there will be leaks.
Anyone can take an old O ring and the application into a manufacturer and get qualified and professional assistance as to the product they need, and although they may not be able to sell you the part. Normally they will tell you who in your area has them or can order them.
Bill

> -----Original Message-----
> From:
> 2cylinderhondas@yahoogroups.com [mailto:2cylinderhondas@yahoogroups.com] > On > Behalf Of > robertjritter > Sent:
> Sunday, October 16, 2011 4:49
> PM
> To:
> 2cylinderhondas@yahoogroups.com
> Subject:
> [2cylinderhondas] Re: More Parts Added
> I have bought many parts from this site and have been very happy with all > the parts I have received and the custom service.
> --- In
> 2cylinderhondas@yahoogroups.com
> ,
> wrote:
> > I wouldn't go so far as to
> qualify these as good parts. Something off the
> > shelf for a different
> application may not work and cause more problems than
> > you had to begin
> with. Natural Rubber works well with water but not with
> > oil, there are
> a bunch of O rings out there made for a different purpose.
> > Many of the
> shaft seals sold by Honda are directional. None of the seals > > listed > have that capacity. Often a seal is not all that is needed to > > correct > the problem, the sealing surface may also need repair. It may fit > > the > housing but will it seal against the rotating shaft? You may have
> noticed the Fan Mount cushions on your engine swelling because of oil
> leaking onto them. If you replaced them with Neoprene rubber they will
> resist swelling and last much longer. The question - have they been > tested > > on a Honda 600 engine? for how long and with what result? In a > vehicle or > > just on a test stand?
> > Bill
> > -----Original Message-----
> > From:
> 2cylinderhondas@yahoogroups.com
> [mailto:
> 2cylinderhondas@yahoogroups.com
> ]On
> Behalf Of Mark P Hatten
> > Sent: Saturday, October 15, 2011 5:27
> PM
> > To:
> 2cylinderhondas@yahoogroups.com
> Subject: RE: [2cylinderhondas] More Parts Added
> > Awesome ! you've got some very much needed parts for great > prices
> http://www.mphspecialties.com/
> ---------------------------------------------------------- > > --
> To:
> 2cylinderhondas@yahoogroups.com
> From: theenginebuilder@...
> > Date: Sat, 15 Oct 2011 22:18:32
> +0000
> > Subject: [2cylinderhondas] More Parts Added
> > More new parts added.
> http://www.honda600carparts.com

amareto23 · Post by **amareto23** » Mon Oct 17, 2011 3:23 am

get a life. i've used many replacement seals and o-rings that are not oem
honda with great results. o.d -i.d dimentions right = no leak. use some
common sense. KEEP the parts coming EngineBuilder! i'm a cetified 40yr.
tech bumper to bumper. My quess is that when you see my 600 you'll cry.
Michael King Kings Klassics
57-Year-Old Mom Looks 25
Mom Reveals $5 Wrinkle Trick That Has Angered Doctors!
http://thirdpartyoffers.juno.com/TGL314 ... 693st04duc

Random Name · Post by **Random Name** » Mon Oct 17, 2011 8:10 am

Let's see it King and does this place that has these parts have a web site?
Kurt

amareto23 · Post by **amareto23** » Mon Oct 17, 2011 12:57 pm

know your seal sizes and match em' up. knowing hydraulic repair shop
owners help with seal manufacture sources. pictures of the micro munster
coming soon!
Get Free Email with Video Mail & Video Chat!
http://www.juno.com/freeemail?refcd=JUTAGOUT1FREM0210

feltonminicycle · Post by **feltonminicycle** » Mon Oct 17, 2011 9:10 pm

As I recall I was Giving It Away with a rebuilt master cylinder. I got it from an industrial supply hose retailer who told me it would work for brake fluid. It was years later I noticed fluid *sweating* through my hose and warned customers it was not a good match.
Miles

--- In
2cylinderhondas@yahoogroups.com
, wrote:
> Bob;
> That may be true, and it is not just this site I am speaking of. There were
> people selling vinyl tubing to be used with brake fluid that was made for
> water. The seals pictured are not directional and there is no mention of
> the material they are made of. If it were a substantiated company such as
> Beck Arnley or WIX there would be no hesitation and I would agree. But who
> knows? Oh they may run for a while but why would Honda make them directional
> if it didn't have to? And, if the O rings are made of Natural Rubber they
> will swell when used with oil and there will be leaks. Anyone can take an
> old O ring and the application into a manufacturer and get qualified and
> professional assistance as to the product they need, and although they may
> not be able to sell you the part. Normally they will tell you who in your
> area has them or can order them.
> Bill
> -----Original Message-----
> From:
2cylinderhondas@yahoogroups.com
> [mailto:
2cylinderhondas@yahoogroups.com
]On Behalf Of robertjritter
> Sent: Sunday, October 16, 2011 4:49 PM
> To:
2cylinderhondas@yahoogroups.com
> Subject: [2cylinderhondas] Re: More Parts Added
> I have bought many parts from this site and have been very happy with all
> the parts I have received and the custom service.
> --- In
2cylinderhondas@yahoogroups.com
, wrote:
> > I wouldn't go so far as to qualify these as good parts. Something off
> the
> > shelf for a different application may not work and cause more problems
> than
> > you had to begin with. Natural Rubber works well with water but not with
> > oil, there are a bunch of O rings out there made for a different
> purpose.
> > Many of the shaft seals sold by Honda are directional. None of the seals
> > listed have that capacity. Often a seal is not all that is needed to
> > correct the problem, the sealing surface may also need repair. It may
> fit
> > the housing but will it seal against the rotating shaft? You may have
> > noticed the Fan Mount cushions on your engine swelling because of oil
> > leaking onto them. If you replaced them with Neoprene rubber they will
> > resist swelling and last much longer. The question - have they been
> tested
> > on a Honda 600 engine? for how long and with what result? In a vehicle
> or
> > just on a test stand?
> > Bill
> > -----Original Message-----
> > From:
2cylinderhondas@yahoogroups.com
> > [mailto:
2cylinderhondas@yahoogroups.com
]On Behalf Of Mark P Hatten
> > Sent: Saturday, October 15, 2011 5:27 PM
> > To:
2cylinderhondas@yahoogroups.com
> > Subject: RE: [2cylinderhondas] More Parts Added
> > Awesome ! you've got some very much needed parts for great prices
http://www.mphspecialties.com/
> > ----------------------------------------------------------
> > --
> > To:
2cylinderhondas@yahoogroups.com
> > From: theenginebuilder@
> > Date: Sat, 15 Oct 2011 22:18:32 +0000
> > Subject: [2cylinderhondas] More Parts Added
> > More new parts added.
http://www.honda600carparts.com