Bill hirsch tank kit

[bobs600honda]

I am on step 2 of 3 , etching.
I followed the instructions and have been drying all day in 100 degree tracy heat. Hooked up the exhaust end of a shop vac and blew hot air through it for a good hour.
Per the instructions, going to wait until tomorrow to start sealer step.
Looking inside the tank, bottom looks white-ish but only about 1/2 way up the side,
Should I get more etch and redo this step or proceed with final step?
Will call bill hirsch in the morning as well to see what he says.
Bob

[Eric Geiger]

As with almost any job the final result is only as good as the prep before it.   There's no harm in etching it twice IMHO.
Eric J. Geiger
---------------------------------------
PRG Nocturne
XXX-XXX-XXXX phone
XXX-XXX-XXXX fax
XXX-XXX-XXXX mobile
egeiger@...
www.prgnocturne.com

On Jun 27, 2013, at 3:43 PM, "bobs600honda" wrote:
I am on step 2 of 3 , etching.
I followed the instructions and have been drying all day in 100 degree tracy heat. Hooked up the exhaust end of a shop vac and blew hot air through it for a good hour.
Per the instructions, going to wait until tomorrow to start sealer step.
Looking inside the tank, bottom looks white-ish but only about 1/2 way up the side,
Should I get more etch and redo this step or proceed with final step?
Will call bill hirsch in the morning as well to see what he says.
Bob

[Robert James]

Thanks Eric. �I was thinking (and hoping!) that a double dose might do the trick. I will give Bill Hirsch a call tomorrow to see what they have to say. �I am in no hurry in that I want to get this right before I put the tank back in!
Thanks again for your comments.
Bob

On Thu, Jun 27, 2013 at 7:47 PM, Eric Geiger
�
> As with almost any job the final result is only as good as the prep before it. � There's no harm in etching it twice IMHO.
> Eric J. Geiger
> ---------------------------------------
> PRG Nocturne
> XXX-XXX-XXXX
> phone
> XXX-XXX-XXXX
> fax
> XXX-XXX-XXXX
> mobile
> egeiger@...
> www.prgnocturne.com
> On Jun 27, 2013, at 3:43 PM, "bobs600honda" rjamesblues@...
> > wrote:
> > �
> > I am on step 2 of 3 , etching.
> > I followed the instructions and have been drying all day in 100 degree tracy heat. Hooked up the exhaust end of a shop vac and blew hot air through it for a good hour.
> > Per the instructions, going to wait until tomorrow to start sealer step.
> > Looking inside the tank, bottom looks white-ish but only about 1/2 way up the side,
> > Should I get more etch and redo this step or proceed with final step?
> > Will call bill hirsch in the morning as well to see what he says.
> > Bob

[Eddie Velasquez]

i need to sell my 72 an 600 $2500. needs brakes one owner title.  very original, car rust on front fenders, sitting for 20 yrs . i crank it up about once a year. eddie @ XXX-XXX-XXXX

[Charles Gould]

Where is the car located?

On Jun 29, 2013, at 10:16 PM, Eddie Velasquez wrote:
> i need to sell my 72 an 600 $2500. needs brakes one owner title.  very original, car rust on front fenders, sitting for 20 yrs . i crank it up about once a year. eddie @ XXX-XXX-XXXX