I am sure I have done this 25 years ago, but don't recall anything other than the 2 bolts inside the car and the 2 in the front corners of the subframe.
What's the easiest way to get the suspension loose? (seems like I unthreaded the tie rod ends before).
Thanks for any hints
need to drop engine out of sedan, any hints?
-
tgm_enterprizes
- Posts: 32
- Joined: Mon Sep 27, 2010 11:59 am
-
Herbert McCoy
- Posts: 0
- Joined: Sun Oct 10, 2010 11:21 pm
Re: need to drop engine out of sedan, any hints?
I am looking for the tool used to take the flywheel off for the 600 sedan. I need to buy barrow or get the measurements to have one made. I have an out standing machinist that lives close by.
Thanks Herb From:
tgm_enterprizes To:
anzhonda600owners@yahoogroups.com Sent:
Fri, November 5, 2010 12:36:00 PM Subject:
[anzhonda600owners] need to drop engine out of sedan, any hints?
I am sure I have done this 25 years ago, but don't recall anything other than the 2 bolts inside the car and the 2 in the front corners of the subframe.
What's the easiest way to get the suspension loose? (seems like I unthreaded the tie rod ends before).
Thanks for any hints
Thanks Herb From:
tgm_enterprizes To:
anzhonda600owners@yahoogroups.com Sent:
Fri, November 5, 2010 12:36:00 PM Subject:
[anzhonda600owners] need to drop engine out of sedan, any hints?
I am sure I have done this 25 years ago, but don't recall anything other than the 2 bolts inside the car and the 2 in the front corners of the subframe.
What's the easiest way to get the suspension loose? (seems like I unthreaded the tie rod ends before).
Thanks for any hints
Re: need to drop engine out of sedan, any hints?
It is my understanding that an engine oil drain plug for a VW Toureg will work as a tool. You have to put a spacer shim in between it and the crank as it's not quite long enough.
From:
Herbert McCoy To:
anzhonda600owners@yahoogroups.com Sent:
Fri, November 5, 2010 11:50:20 AM Subject:
Re:
[anzhonda600owners] need to drop engine out of sedan, any hints?
I am looking for the tool used to take the flywheel off for the 600 sedan. I need to buy barrow or get the measurements to have one made. I have an out standing machinist that lives close by.
Thanks Herb From:
tgm_enterprizes To:
anzhonda600owners@yahoogroups.com Sent:
Fri, November 5, 2010 12:36:00 PM Subject:
[anzhonda600owners] need to drop engine out of sedan, any hints?
I am sure I have done this 25 years ago, but don't recall anything other than the 2 bolts inside the car and the 2 in the front corners of the subframe.
What's the easiest way to get the suspension loose? (seems like I unthreaded the tie rod ends before).
Thanks for any hints
From:
Herbert McCoy To:
anzhonda600owners@yahoogroups.com Sent:
Fri, November 5, 2010 11:50:20 AM Subject:
Re:
[anzhonda600owners] need to drop engine out of sedan, any hints?
I am looking for the tool used to take the flywheel off for the 600 sedan. I need to buy barrow or get the measurements to have one made. I have an out standing machinist that lives close by.
Thanks Herb From:
tgm_enterprizes To:
anzhonda600owners@yahoogroups.com Sent:
Fri, November 5, 2010 12:36:00 PM Subject:
[anzhonda600owners] need to drop engine out of sedan, any hints?
I am sure I have done this 25 years ago, but don't recall anything other than the 2 bolts inside the car and the 2 in the front corners of the subframe.
What's the easiest way to get the suspension loose? (seems like I unthreaded the tie rod ends before).
Thanks for any hints
-
tgm_enterprizes
- Posts: 32
- Joined: Mon Sep 27, 2010 11:59 am
Re: need to drop engine out of sedan, any hints?
--- In anzhonda600owners@yahoogroups.com, "tgm_enterprizes" wrote:
> I am sure I have done this 25 years ago, but don't recall anything other than the 2 bolts inside the car and the 2 in the front corners of the subframe.
> What's the easiest way to get the suspension loose? (seems like I unthreaded the tie rod ends before).
> Thanks for any hints
> any suggestions?