Copue Hatch Glass

[Dave]

I have a near perfect hatch for a coupe. I also have a piece of factory
glass to put into the hatch. I have the service and parts manual but
can't figure out what holds the glass into the hatch. I would
appreciate some help with this,thanx.
Dave Kohn
Long Island,NY

[scott lesniak]

You will have to take it to your local windshield place and they can urethane it in place .
Do not do it yourself unless you have glass primer or it will fall out ,the glass is ceramic coated and it will fall out if you don't use primer.
also the so called primerless urethane will not work either.. I just had mine done and it cost $10 bucks

--- On
Wed, 2/11/09, Dave

wrote:
From: Dave
Subject: [2cylinderhondas] Copue Hatch Glass
To: 2cylinderhondas@yahoogroups.com
Date: Wednesday, February 11, 2009, 6:47 PM
I have a near perfect hatch for a coupe. I also have a piece of factory glass to put into the hatch. I have the service and parts manual but can't figure out what holds the glass into the hatch. I would appreciate some help with this,thanx.
Dave Kohn
Long Island,NY

[mterrens]

I wonder, how was hatch glass installed at the factory?  Mine is glued in; photos I have seen suggest that most are these days.
Steve
www.honda600coupe.com

> ----- Original Message -----
> From:
> scott
> lesniak
> To:
> 2cylinderhondas@yahoogroups.com
> Sent:
> Wednesday, February 11, 2009 7:37
> PM
> Subject:
> Re: [2cylinderhondas] Copue
> Hatch Glass
> You will have to take it to your local windshield place and they > can urethane it in place .
> Do not do it yourself unless you have glass primer or it will fall > out ,the glass is ceramic coated and it will fall out if you don't use > primer.
> also the so called primerless urethane will not work either.. I > just had mine done and it cost $10 bucks > --- On > Wed, > 2/11/09, Dave >
> wrote:
> > From: Dave
> >
> > Subject: [2cylinderhondas] Copue
> > Hatch Glass
> > To: 2cylinderhondas@ yahoogroups. com
> > Date:
> > Wednesday, February 11, 2009, 6:47 PM
> > I have a near perfect hatch for a coupe. I also have a piece of > > factory > > glass to put into the hatch. I have the service and parts > > manual but > > can't figure out what holds the glass into the hatch. I > > would > > appreciate some help with this,thanx.
> > Dave
> > Kohn
> > Long
> > Island,NY

[scott lesniak]

The Original way was with a white ureathane.
I can't think of any suppliers at the moment for white
Scott

--- On
Wed, 2/11/09, Steven Michelsen

wrote:
From: Steven Michelsen
Subject: Re: [2cylinderhondas] Copue Hatch Glass
To: 2cylinderhondas@yahoogroups.com
Date: Wednesday, February 11, 2009, 7:45 PM
I wonder, how was hatch glass installed at the factory?  Mine is glued in; photos I have seen suggest that most are these days.
Steve
www.honda600coupe. com
> ----- Original Message -----
> From:
> scott lesniak
> To:
> 2cylinderhondas@ yahoogroups. com
> Sent:
> Wednesday, February 11, 2009 7:37 PM
> Subject:
> Re: [2cylinderhondas] Copue Hatch Glass
> You will have to take it to your local windshield place and they can urethane it in place .
> Do not do it yourself unless you have glass primer or it will fall out ,the glass is ceramic coated and it will fall out if you don't use primer.
> also the so called primerless urethane will not work either.. I just had mine done and it cost $10 bucks > --- On > Wed, 2/11/09, Dave > > wrote:
> > From: Dave
> > Subject: [2cylinderhondas] Copue Hatch Glass
> > To: 2cylinderhondas@ yahoogroups. com
> > Date: Wednesday, February 11, 2009, 6:47 PM
> > I have a near perfect hatch for a coupe. I also have a piece of factory > > glass to put into the hatch. I have the service and parts manual but > > can't figure out what holds the glass into the hatch. I would > > appreciate some help with this,thanx.
> > Dave Kohn
> > Long Island,NY

[friend]

All;
   3M has a product called Windo-Weld, part number 51135 08612, it is a Ribbon Sealer Auto Glass Replacement Kit.
I still have some from a kit I purchased in 2001, cost then was $11.00 for 15 feet by 3/8 inch thick.
    You have to clean the glass really good, I use a silicone primer and clean the plastic on the hatch and I use a product called Grows Super Clean, to clean the plastic.   Then lay out the windo-weld and set the glass in it.  And your done.  Some like to put a U shaped rubber seal around the glass before placing it on the hatch but they still had to use the windo-weld on the back side and edge for a good fit.
Bill

> -----Original Message-----
> From:
> 2cylinderhondas@yahoogroups.com [mailto:2cylinderhondas@yahoogroups.com] > On > Behalf Of > Steven Michelsen > Sent:
> Wednesday, February 11, 2009
> 4:46 PM
> To:
> 2cylinderhondas@yahoogroups.com
> Subject:
> Re:
> [2cylinderhondas] Copue Hatch Glass
> I wonder, how was hatch glass installed at the
> factory?  Mine is glued in; photos I have seen suggest that most are > these days.
> Steve
> www.honda600coupe. com
> > ----- Original Message -----
> > From:
> > scott
> > lesniak
> > To:
> > 2cylinderhondas@ yahoogroups. com
> > Sent:
> > Wednesday, February 11, 2009 7:37
> > PM
> > Subject:
> > Re: [2cylinderhondas] Copue
> > Hatch Glass
> > You will have to take it to your local windshield place and they > > can urethane it in place .
> > Do not do it yourself unless you have glass primer or it will > > fall out ,the glass is ceramic coated and it will fall out if you > > don't use primer.
> > also the so called primerless urethane will not work either.. I > > just had mine done and it cost $10 bucks > > --- On > > Wed, > > 2/11/09, Dave > >
> > wrote:
> > > From: Dave
> > >
> > > Subject: [2cylinderhondas] Copue
> > > Hatch Glass
> > > To:
> > > 2cylinderhondas@ yahoogroups. com
> > > Date: Wednesday,
> > > February 11, 2009, 6:47 PM
> > > I have a near perfect hatch for a coupe. I also have a piece of > > > factory > > > glass to put into the hatch. I have the service and > > > parts manual but > > > can't figure out what holds the glass into the > > > hatch. I would > > > appreciate some help with this,thanx.
> > > Dave
> > > Kohn
> > > Long
> > > Island,NY