tires/wheels

Joe S. · Post by **Joe S.** » Tue May 05, 2009 8:37 pm

has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it

bottom cop · Post by **bottom cop** » Tue May 05, 2009 9:06 pm

I've never seen a complete list of the vehicles that have the same bolt pattern as the Honda 600 but I'll bet it is a very short list. I do not believe there are any that will fit from newer Hondas Some people have used the RX-7 13" factory aluminum wheels with 50 series tires so the tires will be the same height as the original 10' ones. The Honda 600 bolt pattern is 4 x 110mm so there are not many options out there. There are some 10" mags around but they are usually hard to find. You will hear people say that using anything other than the original 10" tires will put too much stress on the wheel bearings and this could result in a lot of expensive damage. I have to leave that discussion to the experts. 10" tires are available in several levels of quality, it just depends how much you are willing to pay.
--- On Tue, 5/5/09, Joe S. wrote:

> From: Joe S.
> Subject: [2
> cylinderhondas
> ] tires/wheels
> To: 2cylinderhondas@yahoogroups.com
> Date: Tuesday, May 5, 2009, 11:37 PM
> has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it > ------------------------------------

Joe S. · Post by **Joe S.** » Tue May 05, 2009 9:15 pm

thanks for the info just wondering if i wanted to go bigger if i had to do something custom or stay with stock was thinkin about adapting over to a different hub

--- In
2cylinderhondas@yahoogroups.com
, bottom cop wrote:
> I've never seen a complete list of the vehicles that have the same bolt pattern as the Honda 600 but I'll bet it is a very short list.� I do not believe there are any that will fit from newer Hondas� Some people have used the RX-7 13" factory aluminum wheels with 50 series tires so the tires will be the same height as the original 10' ones.� The Honda 600 bolt pattern is 4 x 110mm so there are not many options out there.� There are some 10" mags around but they are usually hard to find.� You will hear people say that using anything other than the original 10" tires will put too much stress on the wheel bearings and this could result in a lot of expensive damage.� I have to leave that discussion to the experts.� 10" tires are available in several levels of quality, it just depends how much you are willing to pay.
> --- On Tue, 5/5/09, Joe S. wrote:
> From: Joe S.
> Subject: [2cylinderhondas] tires/wheels
> To:
2cylinderhondas@yahoogroups.com
> Date: Tuesday, May 5, 2009, 11:37 PM
> has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it
> ------------------------------------

Joe S. · Post by **Joe S.** » Tue May 05, 2009 9:19 pm

i was at a car show over the weekend and saw 2 600's http://i483.photobucket.com/albums/rr19 ... 0_0147.jpg check it out

--- In
2cylinderhondas@yahoogroups.com
, "Joe S." wrote:
> thanks for the info just wondering if i wanted to go bigger if i had to do something custom or stay with stock was thinkin about adapting over to a different hub
> --- In
2cylinderhondas@yahoogroups.com
, bottom cop wrote:
> > I've never seen a complete list of the vehicles that have the same bolt pattern as the Honda 600 but I'll bet it is a very short list.� I do not believe there are any that will fit from newer Hondas� Some people have used the RX-7 13" factory aluminum wheels with 50 series tires so the tires will be the same height as the original 10' ones.� The Honda 600 bolt pattern is 4 x 110mm so there are not many options out there.� There are some 10" mags around but they are usually hard to find.� You will hear people say that using anything other than the original 10" tires will put too much stress on the wheel bearings and this could result in a lot of expensive damage.� I have to leave that discussion to the experts.� 10" tires are available in several levels of quality, it just depends how much you are willing to pay.
> > --- On Tue, 5/5/09, Joe S. wrote:
> > From: Joe S.
> > Subject: [2cylinderhondas] tires/wheels
> > To:
2cylinderhondas@yahoogroups.com
> > Date: Tuesday, May 5, 2009, 11:37 PM
> > has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it
> > ------------------------------------

Tom Feick · Post by **Tom Feick** » Wed May 06, 2009 6:41 am

I have been wondering the same thing because I'm not finding a huge selection of 10" tires. Tire Rack has 10" Kumho's for $46 a piece + shipping. Discount Tire (America's Tire) can get the 10" and install them for $66 a piece.

--- On Wed, 5/6/09, bottom cop wrote:
> From: bottom cop Subject: Re: [2cylinderhondas] tires/wheels
> To:
2cylinderhondas@yahoogroups.com
> Date: Wednesday, May 6, 2009, 12:06 AM
> I've never seen a complete list of
> the vehicles that have the same bolt pattern as the Honda
> 600 but I'll bet it is a very short list.� I do not
> believe there are any that will fit from newer Hondas�
> Some people have used the RX-7 13" factory aluminum
> wheels with 50 series tires so the tires will be the same
> height as the original 10' ones.� The Honda 600
> bolt pattern is 4 x 110mm so there are not many options out
> there.� There are some 10" mags around but they
> are usually hard to find.� You will hear people say
> that using anything other than the original 10" tires
> will put too much stress on the wheel bearings and this
> could result in a lot of expensive damage.� I have to
> leave that discussion to the experts.� 10" tires
> are available in several levels of quality, it just depends
> how much you are willing to pay.
> --- On
> Tue, 5/5/09, Joe S. yahoo.com> wrote:
> From: Joe S.
> Subject: [2cylinderhondas] tires/wheels
> To: 2cylinderhondas@ yahoogroups. com
> Date: Tuesday, May 5, 2009, 11:37 PM
> has anyone ever put a different size
> wheel on these cars, and because its a honda could i put a
> 13" honda wheel on it
> ------------ --------- --------- ------

breacpa · Post by **breacpa** » Wed May 06, 2009 8:29 am

You might take a look at Mini Mania online. They have a few 10" tires listed.
Here is the link:
http://www.minimania.com/web/STSearch/T ... entory.cfm
In a message dated 05/06/2009 06:41:15 A.M. Pacific Daylight Time, franknfike@... writes:

> I
> have been wondering the same thing because I'm not finding a huge selection of > 10" tires. Tire Rack has 10" Kumho's for $46 a piece + shipping. Discount Tire > (America's Tire) can get the 10" and install them for $66 a piece.
> ---
> On Wed, 5/6/09, bottom cop wrote:
> > From:
> bottom cop
> > Subject: Re: [2cylinderhondas]
> tires/wheels
> > To: 2cylinderhondas@yahoogroups.com
> > Date:
> Wednesday, May 6, 2009, 12:06 AM
> > I've never seen a complete list of
> the vehicles that have the same bolt pattern as the Honda > > 600 but I'll > bet it is a very short list. I do not > > believe there are any that > will fit from newer Hondas > > Some people have used the RX-7 13" > factory aluminum > > wheels with 50 series tires so the tires will be the > same > > height as the original 10' ones. The Honda 600 > > bolt > pattern is 4 x 110mm so there are not many options out > > there.
> There are some 10" mags around but they
> > are usually hard to
> find. You will hear people say
> > that using anything other than
> the original 10" tires
> > will put too much stress on the wheel bearings
> and this
> > could result in a lot of expensive damage. I have
> to
> > leave that discussion to the experts. 10" tires
> > are
> available in several levels of quality, it just depends
> > how much you
> are willing to pay.
> > --- On
> > Tue, 5/5/09, Joe S.
> > yahoo.com> wrote:
> > From:
> Joe S.
> > Subject: [2cylinderhondas]
> tires/wheels
> > To: 2cylinderhondas@ yahoogroups. com
> > Date:
> Tuesday, May 5, 2009, 11:37 PM
> > has anyone ever put a
> different size
> > wheel on these cars, and because its a honda could i
> put a
> > 13" honda wheel on it
> ------------ --------- --------- ------
> > Yahoo! Groups
> Links
> > (Yahoo! ID required)
> > mailto:2cylinderhondas-
> > fullfeatured@
> yahoogroups. com
> > unsubscribe@ yahoogroups. com
> ------------------------------------
> Yahoo! Groups
> Links
> To

Big savings on Dell's most popular laptops. Now starting at $449!

riceburner006 · Post by **riceburner006** » Wed May 06, 2009 8:33 am

--- In
2cylinderhondas@yahoogroups.com
, "Joe S." wrote:
I heard there also was a 12" wheel from an early mazda car and pickup that had same bolt pattern. I searched for quite awhile without luck! The 12" tires,if they clear the body,would be great for hi-way trips!
> has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it

Joe S. · Post by **Joe S.** » Wed May 06, 2009 10:15 am

anyone know of a tire size converter online that has 10" tires on it i have found plenty for 12" and up as far as finding something that i can put on there staying the same size

--- In
2cylinderhondas@yahoogroups.com
, "riceburner006" wrote:
> --- In
2cylinderhondas@yahoogroups.com
, "Joe S." wrote:
> I heard there also was a 12" wheel from an early mazda car and pickup that had same bolt pattern. I searched for quite awhile without luck! The 12" tires,if they clear the body,would be great for hi-way trips!
> > has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it

Steve Bryant · Post by **Steve Bryant** » Wed May 06, 2009 10:50 am

http://www.miata.net/garage/tirecalc.html I found this one, but it doesn't have 10" if you want at the bottom type in the sizes to compare - it will give you the % increase or decrease...
Hope this helps, If nothing else - maybe contact these guys and ask them if they would include 10" in their tire size...
Steve Bryant From:
Joe S.
To:
2cylinderhondas@yahoogroups.com Sent:
Wednesday, May 6, 2009 11:14:38 AM Subject:
[2cylinderhondas] Re: tires/wheels
anyone know of a tire size converter online that has 10" tires on it i have found plenty for 12" and up as far as finding something that i can put on there staying the same size

--- In
2cylinderhondas@ yahoogroups. com
, "riceburner006" wrote:
> --- In
2cylinderhondas@ yahoogroups. com
, "Joe S." wrote:
> I heard there also was a 12" wheel from an early mazda car and pickup that had same bolt pattern. I searched for quite awhile without luck! The 12" tires,if they clear the body,would be great for hi-way trips!
> > has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it

Miles · Post by **Miles** » Wed May 06, 2009 9:23 pm

I used to have a set of mags that were 12" that fit Honda 600. I sold them to a friend who has a Toyota s800 2 cylinder car, same bolt pattern. Same bolt pattern as Mazda and if you get Mazda 13" wheels and use low profile tires you will be about the same height as the n600 tire.
If you search the archived messages you will see the bigger wheel question about once a month.
It might be the Mazda R100 that had 12" wheels.
Miles

--- In
2cylinderhondas@yahoogroups.com
, "riceburner006" wrote:
> --- In
2cylinderhondas@yahoogroups.com
, "Joe S." wrote:
> I heard there also was a 12" wheel from an early mazda car and pickup that had same bolt pattern. I searched for quite awhile without luck! The 12" tires,if they clear the body,would be great for hi-way trips!
> > has anyone ever put a different size wheel on these cars, and because its a honda could i put a 13" honda wheel on it